Printing Guide
Settings, orientation, and fit tuning for printing the box and lid, plus the small calibration prints that check a fit before you commit to a full box.
Baseline FDM Settings
Section titled “Baseline FDM Settings”- Nozzle:
0.4 mm - Layer height:
0.20 mm - Walls/perimeters:
3+ - Top/bottom layers:
4+ - Infill:
15%to25% - Material: PLA or PETG recommended for first-fit calibration
Print Validation Status
Section titled “Print Validation Status”Most of this model is checked by a geometry regression suite, which proves that the solids are the shape and the count they should be. It cannot prove that a part prints well, that a clip holds, or that two pieces fit. Only a print does that.
This table records what has actually been printed. A feature marked rendered only is not known to be broken; it is simply untested in filament. Print a fit test box first when you use one.
| Feature | Status | What the print showed |
|---|---|---|
| Box body, walls and side openings | Printed | The 2.0.0-rc.5 test prints, and the box photographed in README.md |
Lid, both Lid_Style values, and the Lid_Lip_Gap default of 0.15 |
Printed | 0.15 fitted well with both styles, with and without magnets, at rc.5 |
Enable_Lid_Magnets pockets |
Printed | Part of the same rc.5 fit prints |
Enable_Post |
Printed | The photographed box carries one. Its mating lid socket is not shown |
Floor clips, both Clip_Style values |
Printed, with a known weakness | At rc.4 the clips held the piece off the bed, which rc.5 fixed. At rc.5 each half printed its whole floor flat, but the halves could still slide against each other, and the Tab pair’s rims did not meet flush |
| Seam teeth | Rendered only | Added after those prints, to fix the sliding the rc.5 pair showed |
Enable_Stabilizers fins |
Rendered only | The photographed box has none |
Enable_Bottom_Openings floor cutouts |
Rendered only | - |
Lid_Relief_Style Scallop and Tab |
Rendered only | - |
Enable_Gridfinity_Bottom feet |
Rendered only | The shape they replaced was printed at rc.5, and its 4 mm ledge printed as loose loops |
Enable_Gridfinity_Lid_Top baseplate |
Rendered only | The socket it replaced was printed at rc.5, and its 37 mm floor sagged. Printing the pockets upward is the fix, and it is the untested part |
Enable_Gridfinity_Magnet_Screw pockets and screw holes |
Rendered only | - |
All_Opening_Top_Style="Teardrop" |
Rendered only | - |
Bottom_Edge_Style Teardrop and Chamfer |
Rendered only | - |
Every printed row was printed on a Bambu Lab P1S in PLA+, except the photographed box, which is black PETG on an unrecorded machine. A row marked rendered only means this repository holds no record of a print, not that a print failed. Where an earlier version of a feature did fail in print, the row says so, because that failure is why the current shape exists.
Orientation
Section titled “Orientation”- Box: print it as exported, open top facing up.
- Lid: print it as exported. Without a Gridfinity lid top, the lid turns over in use, so the face on the bed becomes the top of the closed box and gets the bed’s finish; the lip, the magnet pockets, and the post socket all face up and print without support.
- Lid with
Enable_Gridfinity_Lid_Top: the model exports it already turned over, so the baseplate pockets face up and nothing bridges across them. The lip’s face is on the bed instead, filled solid, and it is that face which ends up inside the closed box. Print it as exported either way. - Sliced parts: print each piece as exported, so the seam faces stay vertical and the clips keep their designed dimensions.
Fit Test Box
Section titled “Fit Test Box”A small box made with your own settings checks a fit before you spend the filament on a full box. Start from your configuration and change only the size and the extras:
Box_Width=50,Box_Depth=50,Box_Height=12, andLid_Height=4Enable_Post=false,Enable_Stabilizers=false, and everyOpening_On_*set tofalsePart_To_Render="Box and Lid", so both parts export together
Keep every value that affects the fit: Wall_Thickness, Box_Corner_Radius,
Lid_Style, Lid_Lip_Gap, and Clip_Tolerance.
To test one feature, turn on only that feature. Use Enable_Lid_Magnets=true
for the magnets. For a seam, use Box_Width=80, Box_Height=15,
Enable_Slicing=true, Slice_Count=2, and Slice_Piece_To_Render=0, which
exports both halves side by side. For Gridfinity, test a one-cell box against
real Gridfinity parts: set Box_Width=41.5 and Box_Depth=41.5, because the
base rounds a 50 mm box up to 2 x 2 cells.
Fit Calibration Procedure
Section titled “Fit Calibration Procedure”- Print a fit test box, or one full box and lid pair, in the target material and with your usual settings.
- Test the fit after the parts cool fully.
- Adjust
Lid_Lip_Gapby0.05 mmincrements. - Repeat until the fit is right, then use the same value for the real box.
The default Lid_Lip_Gap of 0.15 mm fitted well with both lid styles, with
and without magnets, on a Bambu Lab P1S printing PLA+.
Slicing Mode Print Procedure
Section titled “Slicing Mode Print Procedure”- Enable slicing and choose
Slice_Count. - Export each piece with
Slice_Piece_To_Render=1..Slice_Count. - Print one seam pair first: a two-slice fit test box, or the two pieces that share a seam.
- Tune
Clip_Toleranceby0.05 mmas needed. It sets the clearance of both the clips and the seam teeth. - Print the full set only after the seam fits.
- Push the pieces together along the seam. The teeth hold them level, and the floor clips hold them in line. For a permanent box, put cyanoacrylate glue on the tooth faces before joining; the 45 degree faces give about 1.4 times the glue area of a flat seam.
Every piece sits flat on its floor, so sliced pieces print without support. The seam teeth are at most 45 degrees from vertical, so they need no support either.
Releases up to and including 2.0.0-rc.4 centred each male floor clip on the floor, and 0.575 mm of it hung below the piece. A slicer then stood the whole piece on its clips. Re-export any sliced pieces from those releases.
Side Openings
Section titled “Side Openings”- Round tops, the default, flatten near the top of each arc, and that part prints as an overhang anchored on one side. It spans about 1.5 mm of height at the default 10 mm width, and about 3.5 mm at 24 mm.
All_Opening_Top_Style=Teardropturns each rounded top corner into a 45 degree flank with a short flat cap, so the top prints without support. The opening keeps its typed width and height. The cap is a bridge about 0.41 times the opening’s width, 4 mm at the default, and slicers print a bridge anchored at both ends well.- A square opening,
All_Opening_Corner_Radius=0, already has a straight bridge for a top, soTeardropleaves it unchanged.
Gridfinity
Section titled “Gridfinity”- The box’s feet are solid and stand on the bed. Their sides lean out at 45 degrees or rise straight, so they need no support. Releases through 2.0.0-rc.5 hollowed the base from below and left a 37 mm bridge in every cell.
- With the base on, the footprint rounds up to whole cells, so the box’s walls stand directly on the outer feet and no ledge overhangs them. Releases through 2.0.0-rc.5 left a flat ledge of 4 mm or more around the base, which printed as loose loops without supports.
- Foot magnet pockets open onto the bed, so the magnets go in after printing.
Above each pocket, two bridging layers carry the pocket’s ceiling across the
screw hole. Each is
Print_Layer_Heighttall, 0.2 mm by default. Set it to the layer height you slice at. A slicer samples each layer near its middle height, so a step shorter than your real layers can be skipped, which defeats the technique. - The lid’s pockets open upward when the lid prints as exported, so each floor is printed on solid material rather than bridged. Releases through 2.0.0-rc.6 printed the lid the other way up and each floor was a 37 mm bridge, which sagged and made the sockets too shallow to seat a foot.
- Two short ceilings remain on a Gridfinity lid, both on the face that lands on
the bed. The post socket’s is a disc
Post_Diameter + 2 * Lid_Lip_Gapacross, 15.3 mm at the defaults. WithEnable_Lid_Magnetseach magnet-boss notch adds a ring about 8.9 mm across whose material only reaches 1.35 mm in from its wall. Neither needs support, and nothing else on either part is a flat overhang wider than about 15 mm. - The slab’s rim overhangs the filled plug by about 4 mm all round, which prints as a short unsupported ledge.
- The feet are built to the spec’s numbers, and a spec foot leaves 0.25 mm all round in a spec baseplate pocket. Test a one-cell box against a real baseplate before a full box anyway.
Magnets
Section titled “Magnets”- Pockets open at the box rim and at the lid’s mating face, so both print facing up and the magnets go in after printing. No pause is needed.
- Each pocket takes one magnet: a nominal 6 mm disc up to 2.4 mm thick.
- Insert the magnets with opposing poles facing. The pockets are symmetric, so the model cannot enforce polarity. Glue one pair at a time and check that the pair attracts before the adhesive sets.
- If a press fit cracks a boss, raise
Lid_Magnet_Diameterslightly or thickenLid_Magnet_Wall.
Edge Treatment
Section titled “Edge Treatment”- With the default
Bottom_Edge_Style=Fillet,Bottom_Edge_Filletcurves the box’s bottom edge inward toward the bed, so its lowest layers overhang the bed slightly. Look at those layers on a small test box before you use a large fillet on a full box. Bottom_Edge_Style=Teardropkeeps the rounded look but finishes in a 45 degree chamfer at the bed, so the first layers do not overhang.Bottom_Edge_Style=Chamferis a plain 45 degree bevel, which also hides elephant’s foot.Top_Edge_Chamferfaces up and prints without support.
Common Print Quality Notes
Section titled “Common Print Quality Notes”- If walls feel weak, increase
Wall_Thicknessor perimeter count. - If clips fracture, increase
Clip_Tab_Widthor use tougher material. - If top corners warp (ABS/ASA), use enclosure and bed adhesion aids.
- If the tops of rounded openings droop, set
All_Opening_Top_Style=Teardrop. If a square opening’s top bridge sags, reduce bridge speed and increase cooling.
Post-Processing
Section titled “Post-Processing”- Deburr opening edges lightly before cable routing.
- Dry-fit lid and seams before full cable load.
- If required, lightly sand mating features; avoid over-removal.