Parameter Interactions
This page captures interactions that most affect model behavior and print outcomes.
Side Openings
Section titled “Side Openings”Global vs per-side dimensions
Section titled “Global vs per-side dimensions”- Global:
All_Opening_Width,All_Opening_Height,All_Opening_Corner_Radius - Per-side width/height overrides apply when override value is greater than
0. - Per-side corner-radius overrides apply when override value is
>= 0.
Practical effect:
- Override set to
0means “inherit global”.
Corner-radius behavior:
All_Opening_Corner_Radius = -1keeps fully rounded slot ends.- Side override radius
>= 0takes precedence (0square,>0rounded rectangle).
Global and local offsets combine
Section titled “Global and local offsets combine”Global offset terms are added to side-local terms, but axis semantics differ by wall.
Implication:
- If placement looks wrong, zero global offsets first and tune side-local offsets independently.
The vertical terms combine the same way. An opening’s top edge is
All_Openings_Up + Move_Opening_<wall>_Up + its height. When that passes
Box_Height, the opening is cut open to the rim as a notch and the model
reports it with an echo. When it comes within Wall_Thickness of the rim,
the lid relief on that wall is skipped.
Stabilizers and Side Openings
Section titled “Stabilizers and Side Openings”Opening-avoid toggles suppress stabilizers that would overlap opening zones:
Stabilizer_Avoid_Front_OpeningStabilizer_Avoid_Back_OpeningStabilizer_Avoid_Left_OpeningStabilizer_Avoid_Right_Opening
Interaction risks:
- High fin counts + wide openings can remove many fins, making spacing appear irregular.
Tuning order:
- Set opening sizes/positions
- Set stabilizer count/alignment
- Use avoid toggles
- Adjust spacing (
Stabilizer_FB_Spacing,Stabilizer_LR_Spacing) forCentered/Custom - Adjust margins
Bottom Openings and Center Post
Section titled “Bottom Openings and Center Post”When both are enabled:
Enable_Post=trueEnable_Bottom_Openings=trueBottom_Opening_Avoid_Post=true- Tune
Bottom_Opening_Post_Marginfor required clearance around the post.
Openings are split around center clearance.
Interaction risks:
- High opening count plus large post diameter can crowd one side.
- Orientation and axis combinations can make expected spacing non-intuitive.
Bottom Axis vs Orientation
Section titled “Bottom Axis vs Orientation”These are independent controls:
Bottom_Opening_Axis: sequence directionBottom_Opening_Orientation: opening rotation
Result:
- You can arrange along X while each slot is rotated along Y, and vice versa.
Alignment + Margins
Section titled “Alignment + Margins”Primary and secondary alignments consume margins differently depending on axis.
Examples:
Along X: left/right margins are primary boundsAlong Y: front/back margins are primary bounds
Slicing and Clip Fit
Section titled “Slicing and Clip Fit”Key interaction group:
Clip_ToleranceClip_Tab_WidthClip_Tab_DepthClip_Tab_HeightClips_Per_Edge
Behavior:
- Larger tolerance loosens fit.
- More clips improve registration but increase insertion/removal force and cumulative fit error.
Recommended tuning sequence:
- Keep default clip dimensions
- Tune
Clip_Tolerancefirst - Adjust
Clips_Per_Edgesecond - Adjust tab geometry only if needed
Slicing Preview vs Single Slice Export
Section titled “Slicing Preview vs Single Slice Export”Slice_Piece_To_Render = 0: preview all slicesSlice_Piece_To_Render > 0: exportable single index
Common mistake:
- Exporting with
0when intent was one printable part.
Lid Fit Parameters
Section titled “Lid Fit Parameters”Lid_Stylechooses whether the lip wraps the outside of the box (Skirt) or drops inside the wall (Plug)Lid_Lip_Gapcontrols mating clearance on each side, for both styles and for the post socketLid_Lip_Gap_HeightandLid_Heightaffect engagement and rigidity
Interaction pattern:
- Tightening
Lid_Lip_Gapmay require small increases in height or stronger cooling control for consistent fit. - A Skirt fits against the box’s outside face and a Plug against its inside face, so the same
Lid_Lip_Gapcan feel different between them on one printer. Tune each with its own fit test box. - With
Lid_Style=Plug, the ring is notched aroundEnable_Lid_Magnetsbosses, andStabilizer_HeightandPost_Diametermust leave it room; the model asserts otherwise. - Any side opening that runs to the rim loses its top
Lid_Lip_Gap_Heightunder a seated lid, with either style.
Post and Lid
Section titled “Post and Lid”With Enable_Post=true, both box and lid include post-interface geometry.
Interaction implications:
Post_Diameteraffects center clearance and mating geometry.Closed_Postmodifies box post cavity behavior but does not remove lid-side post logic.
Edge Treatment and Gridfinity
Section titled “Edge Treatment and Gridfinity”Key interaction group:
Bottom_Edge_FilletTop_Edge_ChamferEnable_Gridfinity_BottomEnable_Gridfinity_Lid_Top
Behavior:
- A Gridfinity interface owns the face it sits on, and its profile is dimensioned by the Gridfinity standard. Softening that perimeter would move a mating surface, so the treatment is suppressed there rather than applied and hoped for.
- Suppression is gated on whether an interface actually rendered, not on the
Enable_parameter. A box too small for even one 42 mm cell renders no base, and keeps its fillet. - The box bottom and the lid’s exposed face are the two suppressed cases. The box rim is never suppressed, because no Gridfinity feature touches it.
Lid Relief and Side Openings
Section titled “Lid Relief and Side Openings”Key interaction group:
Lid_Relief_Style,Lid_Relief_On_*All_Opening_Height,Override_Opening_Height_*,All_Openings_Up
Behavior:
- Relief is cut into the lid; openings are cut into the box. At default sizes they are nowhere near each other, so most configurations need no thought.
- They meet only when an opening runs to the box rim. Then the relief on that wall is dropped: a tab would stand over a hole and a scallop would open into it, and neither gives anything to grip.
- The skip is automatic and silent. If a relief you asked for is missing, check whether that wall’s opening reaches the rim.
Lid Magnets and Everything Else
Section titled “Lid Magnets and Everything Else”Key interaction group:
Enable_Lid_Magnets,Lid_Magnet_Diameter,Lid_Magnet_WallPost_Diameter,Enable_Slicing,Box_Corner_Radius
Behavior:
- Magnets sit in bosses at the four inside corners. That placement is what keeps them clear of everything else: openings sit on wall centres, stabilizers carry end margins, the post is central, and slice seams sit at interior x.
- The only collisions left are with the post on a small box, and with the opposite corner on a very small one. Both assert rather than merging silently.
Box_Corner_Radiusdoes not need to accommodate the boss. The boss is pushedWELDinto both walls, so it fuses whether or not the rounded corner reaches it.
Quick Diagnostic Matrix
Section titled “Quick Diagnostic Matrix”If issue is mostly…
- Opening placement drift: inspect global+local opening offsets.
- Missing stabilizers: inspect opening-avoid toggles and fin count/margins.
- Bottom opening crowding: inspect axis/orientation/post-avoid combination.
- Slice fit too tight/loose: inspect clip tolerance before tab dimensions.
- Lid fit issues: inspect lip gap first, then print-process factors.