Parametric Cable Box

Every option, shown

A visual reference for the parametric cable management box. Each parameter below is rendered from the model itself, so what you see is what it builds.

Model 2.0.0 OpenSCAD 2021.01+ MIT licensed Self-contained, works offline

Getting started

Two ways in, depending on whether you want to adjust anything.

If you wantDo this
A ready-to-print fileGrab an STL from library/ or from the GitHub Releases page. No software needed beyond a slicer.
To change the dimensionsOpen cable-box-parametric.scad in OpenSCAD, open the Customizer from the Window menu, adjust, then press F6 to render and export.
To start from a presetOpen cable-box-parametric.scad, show the Customizer, and pick a preset from its dropdown, then tweak. The dropdown reads cable-box-parametric.json, which sits beside the model.
Dimensions are outer dimensions. Box_Width, Box_Depth, and Box_Height describe the outside of the shell. Usable interior is smaller by Wall_Thickness on each side, and smaller again wherever stabilizer fins sit.

Overall

What gets generated.

Box Only
Box Only
Lid Only
Lid Only
Box and Lid
Box and Lid

Box

Shell dimensions and wall.

Default 100 x 75 x 50
Default 100 x 75 x 50
Wide: 200 x 75 x 50
Wide: 200 x 75 x 50
Tall: 100 x 75 x 90
Tall: 100 x 75 x 90
Corner radius 2 (crisp)
Corner radius 2 (crisp)
Corner radius 8.1 (default)
Corner radius 8.1 (default)
Corner radius 25 (soft)
Corner radius 25 (soft)
Wall 1.2 mm
Wall 1.2 mm
Wall 3.0 mm
Wall 3.0 mm

Centre post

The cable-wrapping core.

Post enabled (default)
Post enabled (default)
Post disabled
Post disabled
Post diameter 30
Post diameter 30
Closed_Post: solid floor under the post
Closed_Post: solid floor under the post

Lid

Fit and engagement.

Default lid: Lid_Style Plug, a ring inside the wall
Default lid: Lid_Style Plug, a ring inside the wall
Lid_Style Skirt wraps the box
Lid_Style Skirt wraps the box
Lid_Height 16
Lid_Height 16
Lid_Lip_Gap_Height 8
Lid_Lip_Gap_Height 8

Edges, lid grip and magnets

Optional finishing features. All are off by default.

Bottom_Edge_Fillet 1.5
Bottom_Edge_Fillet 1.5
Bottom_Edge_Style Teardrop: meets the bed at 45 degrees
Bottom_Edge_Style Teardrop: meets the bed at 45 degrees
Bottom_Edge_Style Chamfer
Bottom_Edge_Style Chamfer
Top_Edge_Chamfer 0.8
Top_Edge_Chamfer 0.8
Lid_Relief_Style Scallop
Lid_Relief_Style Scallop
Lid_Relief_Style Tab
Lid_Relief_Style Tab
Enable_Lid_Magnets: corner bosses
Enable_Lid_Magnets: corner bosses

Side openings

Where cables enter and leave.

Default: 10 wide x 30 tall, 5 up from the floor
Default: 10 wide x 30 tall, 5 up from the floor
Width 30
Width 30
Height 15
Height 15
All_Openings_Up 0: flush with the floor
All_Openings_Up 0: flush with the floor
All_Openings_Up 12: lifted further off the floor
All_Openings_Up 12: lifted further off the floor
Corner radius 0: square corners
Corner radius 0: square corners
Corner radius -1: fully rounded (default)
Corner radius -1: fully rounded (default)
All_Opening_Top_Style Teardrop: tops print without support
All_Opening_Top_Style Teardrop: tops print without support
Front and back only
Front and back only
Per-side override: wide front opening
Per-side override: wide front opening

Stabilizer fins

Interior ribs that stiffen the walls.

Disabled
Disabled
3 fins, centred (default)
3 fins, centred (default)
5 fins, distributed
5 fins, distributed
All four walls
All four walls
Taller and deeper fins
Taller and deeper fins

Floor openings

Cutouts through the box floor.

Disabled (default)
Disabled (default)
3 openings along X
3 openings along X
Arranged along Y
Arranged along Y
6 openings, distributed
6 openings, distributed

Slicing for small beds

Split the model into pieces that push together. Floor clips hold them in line, and 45-degree teeth in the walls hold them level.

2 pieces, preview layout
2 pieces, preview layout
3 pieces
3 pieces
Exporting a single piece
Exporting a single piece
4 clips per seam
4 clips per seam
Flat seam, without teeth
Flat seam, without teeth

Gridfinity

Optional interfaces. The box is shown from below, where its feet are, and the lid from above, where its pockets are.

Disabled (default)
Disabled (default)
Feet under the box, rounded up to whole cells
Feet under the box, rounded up to whole cells
Baseplate pockets on the lid
Baseplate pockets on the lid
Both, with magnet and screw holes
Both, with magnet and screw holes